Before we get into the nitty gritty details about how to change a light fixture using a recessed light conversion kit, let’s be clear.
Electricity is like the school bully. He’s good to have on your side, but a nasty, nasty fella if you cross him. DO NOT PLAY WITH ELECTRICITY if you are not CONFIDENT in your skills and knowledge on the subject.
Seriously. Just don’t. Do not pass go, do not collect your linesman pliers, nada.
sneak peak of the recessed light installation process:
And hey, I’m not going to leave all our novice friends in a lurch. If you want to use one of these recessed light conversion kits to swap out a fun, new fixture for an old, cruddy can light, here ya go–> give Amazon Home Services a shout!
You can arrange for them to come and do the wiring for you. The price will vary depending on the exact parameters of the job, but it’s a great option if you’re not completely sure you want to go the DIY route.
Below are the recessed lights that we will be converting to pendants. They are in our kitchen. Here’s the BEFORE:
Supplies needed for changing a light fixture using a recessed light conversion kit:
- recessed light conversion kit
- power screwdriver
- Phillips head screwdriver
How to install a recessed light conversion kit:
1. Turn OFF the breaker
Turn off the breaker for the light/lights you will be working on.**** This step is NOT optional.
2. Unscrew recessed light bulb and remove trim kit.
Unscrew the recessed light bulb from the recessed light fixture. Then remove the “trim kit” which is typically a circular collar that goes around the outer rim of the fixture.
Usually, this piece will simply unsnap from the fixture easily. Once the trim kit is removed, you should be left with the recessed light housing.
3. Screw in lighting harness.
Screw in the new lighting harness into the existing socket where the recessed bulb used to be.
4. Install cross brace.
Install the cross brace hardware. This brace is adjustable, so it should fit most recessed light housings. Extend the bracing across the entire width of the can light housing so that it fits snugly, then tighten the screw in the middle of the brace to set the length.
I wanted to keep it tight enough within the housing so that it was held up there with no screws…this is not necessary, but it makes the next step a little easier.
5. Attach cross brace to recessed housing.
5. Using the two screws provided, attach the cross brace to the recessed housing.
6. Attach lighting support.
Attach the lighting support to the cross brace…two quick screws…no problem!
7. Attach ground wire.
Attach the ground wire to the existing recessed light housing using the clip provided.
You’ve successfully installed your recessed light conversion kit.
Installing the metal backer and medallion is not necessarily required, but because the size of the hole on your ceiling left by the old can light is likely 4-6″ in diameter, you may need to install the metal backer and medallion in order to hide some of that old hole.
Most canopies for a new light you would install are not that large.
8. Twist backer on.
Twist on metal backer.
Super simple. No screws required.
9. Hang medallion.
At this point, you can wire and hang the light fixture of your choice! You can choose a pendant, chandelier, maybe even some cool, budget-friendly DIY lighting.
For our kitchen, we chose a white mini chandelier, with some crystal embellishments. We coupled it with a 16″ ceiling medallion rather than the smaller one which came with the kit.
Hope this comes in handy to you if you’re considering switching out some of your can lights! Ready to get started?
Shop this Post:
Pin this project for later! And if you decide to try it, leave a comment on the pin! That helps others know whether they want to try it, too!
Pssst…before you go, I sure would love to hang out with you again really soon! Sign up now and get a FREE copy of “Builder-Grade To Beautiful: 10 Totally Transformative Home Decorating Solutions, All Under $100!” Click here to enter your email or on the image below. Your copy will be sent right away!
Beautiful transformation. Good to know this can be done by… My husband ??. Thanks for sharing.